PRODUCT DETAILS
The TBS Electronics panel switch (art. 5095000-1) is the matching remote control for the DCM Remote Battery Switch. It is a momentary rocker switch, SPDT (ON)-OFF-(ON): press ON to close the battery contactor, press OFF to open it. The switch is built for the two-wire Set/Reset control method of the Remote Battery Switch.
See the state at a glance
An integrated low-current LED lights when the contact is closed, so you can tell from the panel whether the battery bank is connected.
Sealed for RV and marine panels
Installed with the supplied rubber panel seal, the switch is rated IP65. It fits a 21.0 × 37.0 mm cutout in panels 1.0 to 5.0 mm thick.
How it wires up
See the wiring guide in the product images. Connect the Remote Battery Switch's brown wire to terminal 3 (close), orange to terminal 1 (open) and yellow to terminal 7 (status LED). Feed terminal 2 from battery positive through a 1 A fuse, and link terminal 8 to terminal 2. The Remote Battery Switch's own red wire goes to battery positive through a 6 to 8 A fuse and black goes to ground. Use control mode 1, 2 or 3; mode 3 is the factory setting. The control cable can be extended to 15 m (49 ft).
What's in the bag
One panel switch with rubber panel seal and a printed spec sheet. You supply the control wire, fuses and terminals. A mounting plate is not included.
FEATURES
- Made for the DCM Remote Battery Switch — the matching TBS panel switch (art. 5095000-1) for two-wire Set/Reset control.
- Momentary SPDT (ON)-OFF-(ON) rocker — one side closes the contactor, the other opens it.
- Built-in status LED — low-current indicator, 8 to 30 V DC.
- IP65 when installed with the supplied rubber panel seal.
- Fits panels 1.0 to 5.0 mm thick — cutout drawing on the included spec sheet.
- Panel switch only — wire and mounting plate not included.
WHAT IT RUNS
SPECIFICATIONS
| Model / SKU | TBS art. 5095000-1 / 83820 |
|---|---|
| Switch function | SPDT (ON)-OFF-(ON), momentary |
| Contact ratings | 21 A at 14 V DC; 15 A at 28 V DC |
| Contact resistance | 50 mΩ max. |
| Isolation resistance | 100 MΩ min. at 500 V DC |
| Dielectric strength | 1,500 V AC for 1 minute |
| Indicator (LED) voltage range | 8 to 30 V DC |
| Operating temperature | −25 °C to +85 °C |
| Protection class | IP65 (with rubber seal) |
| Panel cutout | 21.0 × 37.0 mm (0.83 × 1.46 in) |
| Panel thickness | 1.0 to 5.0 mm |
| Face size | 24.4 × 49.5 mm (0.96 × 1.95 in) |
| Weight | 0.74 oz (21 g); 25 g packaged |
| Terminals used | 1 open (orange), 2 fused battery positive, 3 close (brown), 7 status LED (yellow), 8 jumper to 2 |
| Compatible with | TBS DCM Remote Battery Switch (DCM-RBS-12-500), control modes 1 to 3 |
| Included | Panel switch, rubber panel seal, printed spec sheet |
| Not included | Control wire, fuses, terminals, mounting plate |
| Manufacturer | TBS Electronics BV, The Netherlands |
COMPARE MODELS
MANUALS, SAFETY INFORMATION AND DOWNLOADS
ACCESSORIES
FAQ
Does it plug straight into the DCM Remote Battery Switch?
No. You supply the control wire and connect the switch to the 5-wire interface cable that comes with the Remote Battery Switch.
Is a mounting plate included?
No. The switch mounts directly in a panel cutout, in panels 1.0 to 5.0 mm thick. The cutout drawing is on the spec sheet in the bag.
What does the LED show?
The LED lights when the battery contactor is closed, so you can see from the panel that the bank is connected.
Is it waterproof?
It is rated IP65 when installed with the supplied rubber panel seal.